ESSENTIAL DETAILS

Manufacturer	CFSensor
Product Category	Pressure Sensor
Series	XGZP182
Model Number	As Order Guide
Pressure Range	0kPaA～100kPaA…700kPaA
Pressure Type	Absolute
Power Supply	≤15mV or ≤3mA
Output Type	Non-amplified Analog
Output	mV(millivolt)
Bridge Resistance	5kΩ
Measured Media	Air or Non-corrosive Gas or Liquid
Temp. Compensated	0~60°C
Operating Temp	-30~120°C
Package	Plastic Tube or Tape&Reel

APPLICATIONS

Tank level measurement, Liquid level measurement, White goods(e.g.washer), Heating, Ventilation, Air conditioning, Filter detection, Industrial controls.
Medical gas control system, Hospital beds, Massage device, Engine control/manifold absolute pressure (MAP), Green gas( LPG and CNG) control and measurement.
Weather station and weather reporting device barometers, Sport and leisure equipment, Vacuum measurement, pneumatic device, absolute pressure meter.

INTRODUCTION

XGZP182 is a surface mounting pressure sensor based on CFSensor silicon-glass based piezoresistive pressure sensor die. The sensor die is bonded on a substrate with a plastic cap and packaged in a 6-pin SOP. The small size and high reliability of on-chip integration make this sensor a simple and economical choice for high volume application in a variety of industries. With standard SOP8 package, XGZP182 is easy for users to install by SMT assembly.

With good repeatability, linearity, stability and sensibility, XGZP182 is very facile for users to calibrate output & thermal drift and make temperature compensation by using exterior operational amplifier or integrated circuit.(For amplified and calibrated sensor if required,please refer to CFSensor pressure module series).

The XGZP182 pressure sensor is intended for use with non-corrosive gas or air or liquid. It is highly prohibited to choke the side of pressure diaphragm during actual application. Please consult us if a pressure medium other then above media is to be used.

DIMENSION (Unit:mm)

xgzp182 pressure sensor dimension

ORDER GUIDE (100kPa=0.1MPa=1bar≈14.5PSI)

xgzp182 pressure sensor order guide

Datasheet: XGZP182 Pressure Sensor-V2.3.PDF

SAFETY NOTES

Using these sensors products may malfunction due to external interference and surges, therefore, please confirm the performance and quality in actual use. Just in case, please make a safety design on the device (fuse, circuit breaker, such as the installation of protection circuits, multiple devices, etc.), so it would not harm life, body, property, etc even a malfunction occurs. To prevent injuries and accidents, please be sure to observe the following items:

The driving current and voltage should be used below the rated value.
Please follow the terminal connection diagram for wiring. Especially for the reverse connection of the power supply, it will cause an accident due to circuit damage such as heat, smoke, fire, etc.
In order to ensure safety, especially for important uses, please be sure to consider double safety circuit configuration.
Do not apply pressure above the maximum applied pressure. In addition, please be careful not to mix foreign matter into the pressure medium. Otherwise, the sensor will be discarded, or the media will blew out and cause an accident.
Be careful when fixing the product and connecting the pressure inlet. Otherwise, accidents may occur due to sensor scattering and the blowing out of the media.
If the sensor come with sharp PIN, please be careful not to hurt your body when using it.

WARRANTY

The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. CFSensor reserves the right to make changes without further notice to any product herein.

CFSensor makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does CFSensor assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. CFSensor does not convey any license under its patent rights nor the rights of others.